Detection Range Minimum 1 ppb maximum 3000 ppb
Display Range Default 0 ppb to 1000 ppb configurable during commissioning
Repeatability 2% to +2% see Note 1
Accuracy 10% to +10% see Note 1
Measurement Frequency Continuous measurement Modes of 15 20 30 and 60 minutes available upon request
Ambient Temperature Operating range from 0 °C 32 °F to 40 °C 104 °F see Note 2
Water Temperature 1 °C 34 °F to 40 °C 104 °F see Note 2
Analog Output 4 mA to 20 mA scalable to the required range with a maximum load of 900 Ω
Analog Output Isolation 400 V DC
Relay Voltage Maximum 50 V with three relays Alarm 1 Alarm 2 and Fault Relays featuring NO and NC contacts
Relay Current Maximum 5 A
Service Interface USB A to PC using the provided Multisensor Software for the non touchscreen version
Data Storage Uses a μSD card with up to 6 months of storage capacity
Instrument Case Rated IP65 NEMA 4X made of coated mild steel
Instrument Weight 16 kg 35 lbs
Sampling Chamber Material Stainless steel with PVC available as an option
Sampling System Weight 12 kg 26 lbs without water
Sampling System Dimensions 570 x 490 mm 22 x 19 inches
Sampling System Capacity 3 liters 0 79 US gallons
Flow Limit Switch Contacts close if flow falls below the set point option available upon request
Water Flow Rate 2 lmin 0 52 US gpm
System Dimensions 1170 x 490 x 300 mm 46 x 19 2 x 11 8 inches mounted on two separate PVC backboards
Supply Voltage 90 V AC to 240 V AC operating at 50 Hz or 60 Hz
Power Consumption
Standard Version 15 W typical 10 W during operation
Touch Screen Version 45 W typical 20 W during operation
Note 1 Accuracy is ±10% for concentrations between 30 and 3000 ppb calibrated against NIST traceable toluene gas standards under Standard Laboratory Conditions Accuracy can be further improved at points of interest using bespoke calibration
Note 2 Climate control may be required depending on process and ambient conditions
Ini demo, bisa diisi apa saja
Ini demo, bisa diisi apa saja
Ini demo, bisa diisi apa saja
Ini demo, bisa diisi apa saja
Produk Tridinamika tersertifikasi jaminan SNI
Ini hanya demo
Free
Jasa Pengiriman kilat oleh tim Tridinamika
Ini hanya demo saja
2-3 Days
Free
The MS1200 is an on line oil in water analyzer which provides low level measurements of Hydrocarbon Oil and VOCs concentrations in water
Applications
Monitor water abstraction points such as raw river water boreholes and reservoir water
Monitoring for oil in water contamination
Detect VOC contamination in industrial wastewater
Monitor drain and stormwater systems for flammable liquids
Surface water systems for fuel pollution
Offer a monitoring solution for air land remediation and industrial applications
Detect VOC breakthrough in carbon beds
RO membrane protection
Measurement of VOCs in process water
Features and Benefits
No sensor contact with water low maintenance no sensor cleaning
No reagents low running costs
Measures both Polycyclic Aromatic Hydrocarbons PAHs and VOCs
Electronic Nose not affected by turbidity
High sensitivity ideal for potable water
Can be calibrated for specific substances used to monitor known spills
Catches VOC chemical spills not just hydrocarbons
Alarms to SCADA and other communication interfaces
The Oil in Water Analyzer to detect oil spills
Oils and hydrocarbons in general are very often the main components of a wide range of products going from fuels to solvents to many of the chemicals used in the industry during their treatment processes
In industrial production it is possible that some of these hydrocarbons oils and solvents leak into drains or worse directly into the environment
Similarly domestic and agricultural fuel storage can result in accidental spills into water courses and aquifers
This can be a real and huge problem for water supplies and in the worst case threaten the water security of whole communities Often these accidents result into huge fines and expensive cleaning up operations
An Oil in Water Analyser can make the difference by giving an early warning when a problem arises
| Brand |
Multisensor |
|---|
